Preparation steps
Set up bleed and margins
Bleed is extra artwork that extends beyond the trim edge, allowing for slight movement during cutting. Without it, white edges appear on finished pieces.What to do:See Bleed and margins for a detailed explanation of the three zones.
- Add 3 mm of bleed on all sides (standard for most Reprodisseny products).
- Keep text, logos, and important elements at least 3–5 mm inside the trim line (safety zone).
- Extend background colours and images fully into the bleed area.
- Placing text or logos flush against the cut line — even a 1 mm shift during cutting will clip them.
- Forgetting bleed on bleed-to-edge designs. If the design has a white border by intention, no bleed is needed.
Large-format jobs (banners, roll-ups) may require different bleed values. Check with the team if you are unsure.
Work in CMYK
Print presses use four inks — Cyan, Magenta, Yellow, and Black (CMYK). RGB files are converted automatically at output, which can produce unexpected colour shifts.What to do:
- Set your document colour mode to CMYK from the start.
- For critical brand colours, reference Pantone values in addition to CMYK.
- Use 100% K only for small black text — avoid rich black mixes (e.g. C60 M40 Y40 K100) on fine typography, as slight misregistration makes it look blurry.
- Sending files in RGB and expecting exact colour matching.
- Using rich black on body text or small headlines.
- Leaving spot colours (Pantone) unflattened if the job does not require spot printing.
Check image resolution
Low-resolution images print visibly pixelated. Resolution must be measured at the final print size, not the original image dimensions.What to do:
- Use images at 300 ppi at final print size for small and medium format.
- Embed all linked images in the document, or package the file with all links.
- Verify resolution in your application (Photoshop: Image → Image Size; InDesign: Links panel).
- Scaling a 72 ppi web image up to fill a print layout.
- Using screenshots, images copied from websites, or social media exports.
- Placing a low-resolution image and relying on the RIP to compensate.
Handle fonts correctly
Missing fonts are one of the most common pre-press problems. The safest approach is to eliminate the dependency entirely.What to do:
- Convert all text to outlines (curves/paths) before exporting — or embed fonts in the PDF.
- After exporting, open the PDF and check that all text renders correctly, especially special characters and ligatures.
- Review line spacing and kerning after converting to outlines, as some applications adjust metrics on export.
- Sending native files (AI, INDD, PSD) without packaging fonts.
- Using trial fonts or fonts without a commercial print licence.
- Converting to outlines and not proofreading — text cannot be edited afterwards.
When you embed fonts in a PDF rather than converting to outlines, the font data is included in the file. Either approach is acceptable, but outlines are the safest option if you are unsure about font licensing.
Recommended specifications
| Setting | Recommended value |
|---|---|
| Delivery format | PDF (preferred) |
| Colour profile | CMYK (with ICC profile if required) |
| Bleed | 3 mm (standard) |
| Crop marks | Yes, if the design requires them |
| Image resolution | 300 ppi at final print size |
| Transparencies | Flatten if RIP issues occur |
Final checklist
Before sending your file, confirm:- PDF at final size with bleed included (if the design bleeds to the edge)
- Document colour mode is CMYK; images are CMYK or greyscale
- All images are at least 300 ppi at final print size
- Fonts converted to outlines or embedded in the PDF
- No text or important elements within 3 mm of the trim edge
- Crop marks included (if the file is at final size with bleed)
- Transparencies flattened (if required by the job)
Frequently asked questions
Do I need to include crop marks?
Do I need to include crop marks?
If the file is at final size and includes bleed, crop marks help the production team identify the trim position. A well-prepared PDF with marks works perfectly. If you are sending a file without bleed (for example, a white-bordered design), crop marks are not necessary.
What bleed value should I use?
What bleed value should I use?
The standard bleed at Reprodisseny is 3 mm on all sides. For special or large-format products, the required bleed may vary. If you are unsure, contact the team with the product name and they will confirm the correct value.
Should I use RGB or CMYK?
Should I use RGB or CMYK?
CMYK is recommended for all print jobs to ensure colour consistency. For critical corporate colours, specify Pantone references in addition to CMYK values. If you work in RGB (for example, in Photoshop for photo editing), convert to CMYK before exporting your final PDF.
What resolution should my images have?
What resolution should my images have?
300 ppi at the final print size is the standard for small and medium format. For large-format printing (banners, backdrops), the acceptable resolution depends on the intended viewing distance — 100–150 ppi is often sufficient. See Image resolution for detailed guidance.